BETAFPV Lite Brushed Flight Controller [BF-00313125]

The Lite brushed FC V2 is available.

Integrate 25mW VTX, support change VTX channel brand via control.
Add LiteOSD information and OSD Menu.
Support firmware upgrade in DFU mode via USB port.
Integrate an altitude sensor ( altitude hold function is NOT available now).
2 RGB LEDs
Lite Brushed FC User Manual

Since we released the world's first whoop FC with Silverware firmware in 2017, this board become so popular among FPV pilots. Now we have upgraded to the V2 version with a ton of improvement.

Do you want to use your hobby radio transmitter (like Frsky QX7 / X9D etc) to control this drone in Bayang protocol? Want a long range control above 300m? High recommend this newest Bayang Lite RF module. Know more about this LiteModule here.


Key Features
The world's first FC board compatible with Silverware firmware. This must be the most simple and affordable method to try whoop FPV racing hobby.
Support level mode and acro mode. Also it has the ability to change settings for custom builds, or to adapt to personal preferences by stick gestures.
Designed to work with current Tiny Whoop or Blade Inductrix frames
Built in Bayang protocol native receiver, compatible with almost radio transmitter with deviation firmware or deviation compatible transmitter module
The flight controller board comes pre-flashed with Silverware firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.


CPU: STM32F042
Six-Axis: MPU6050
ESC: All FETs are rated at 6.3A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Silverware firmware
Receiver: Bayang protocol
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 2.5g
Silverware & LiteOSD
Silverware is a firmware for some micro quadcopters, which support level mode and acro mode. So you could use this on whoop FPV racing. Also it has the ability to change settings for custom builds, or to adapt to personal preferences.

LiteOSD is also integrated in the V2 board. So that you could setup many configrations according to your own preference easily. The method of entering OSD Menu on Lite Brushed FC is same as Betaflight. Make sure the drone is disarmed when entering OSD Menu on Lite 1S Brushless FC.



-Use Mode 2 (American Mode) as example-
Note: The left throttle stick should be at the middle position and then pull left.
Note: AETR is the default channel mapping of Lite FC. If you can not enter the OSD menu, it might cause by unmatched channel mapping.

If you use a toy transmitter like LiteRadio 1, and also active the TOY_TX option in the OSD menu. You could enter the OSD menu when the throttle stick in the lowest positon.


Supported Radio Transmitter
Currently the built-in receiver is compatible with Bayang protocol. Here is a listing of radio transmitter that could be compatible with this FC board.

LiteRadio Transmitter
BETAFPV LiteModule RF Module ( with PA, range >300m, suit for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR/9XR PRO)
Radio transmitter of toy drone like JJRC H67, Eachine E011 etc, that using the Bayang protocol
Jumper T8SG radio transmitter
MTX-9D multiprotocol module
Other 4in1 multiprotocol module that support the Bayang protocol
If not sure whether your radio transmitter could support this FC board, please email us ( info@betafpv.com) for help.

For example, if you have a Frsky Tanaris QX7 / X9D radio transmitter and want to try this FC board, just plug in a BETAFPV LiteModule RF and done.

Some pilots would complaint that it is definitely not a long range FC. It looses signal with my transmitter far too often and for what appears to be no reason. This issue is often caused by the location of the antenna. You should keep the antenna away from the FC board to get a stronger signal. For example, run the singal upwards. Thanks for Harley Finberg's advice.

【セット内容】
1x BETAFPV Lite brushed flight controller V2.0
4x M1.2x4mm screws (Fit for stock Inductrix frame)
4x M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4x Anti-vibration ruber dampers

この商品を買った人はこんな商品も買っています